The foundation of your patio should be strong if you plan to install one. When byggskiva a high terrace, plintar altan are required; however, when bygghandel a low terrace, concrete slabs can be mounted immediately on top of them. Here, we’ll walk you through the process step-by-step.
Mark the intended size of the plinths balcony and cross-measure it.
The diagonals ought to be equal in length.
Dig down finished plinths or cast plinths balcony using our casting pipes.
The terminals should not be more than 2 meters apart. The terminals must be level and parallel to one another (if you use terminals with adjustable post shoes, there is the possibility of readjustment if the terminals would not be level). The house wall is fastened to the inner carrying rope at a distance of around 10-20mm.
Get off with a lengthy spirit level and use caution.
If you’re going to install a railing around the terrace, posts will be screwed into the terminals. Mount the outer support rope on the plintar altan and exit. The support ropes will be screwed into the posts in this scenario. Continue to wrap the carrying ropes parallel to the wall and around the whole structure. Floor joists (support bars) are fixed with a maximum spacing of 600 mm in between the carrying ropes. To the carrying ropes, floor joists are fastened with nails, screws, or beam shoes.
The pallets are then screwed on.
Start on the outside and go in the direction of the wall. Trolley boards may be set all around to make a wonderful framing for the floor trolley, which will also frame the terrace. A front might be constructed around the terrace for decorative purposes. The plintar altan and space below the front can be covered with finely sawn, impregnated planks or decking.
Using visible screws is one of the most typical deck mounting techniques. If you’re using a hard wood, like Bangkirai, you need to first pre-drill the trolley boards before attaching them using stainless steel trolley screws. The terrace is currently ready!
Things to think about when creating a plinths balcony
Count the patio’s square footage.
No matter what kind of patio foundation you decide on, it is always a good idea to start by drawing down the patio’s dimensions and fictitious corners. Use thread and heavy poles to break off the corners. Then indicate the locations of the ground excavations and the placement of the concrete plinths. Try to get the terminals as straight as you can and keep the distance between them under 2 meters.
Construct the terrace on concrete pillars.
Concrete plinths balcony are often the ideal choice for individuals looking for a particularly strong base for their patio. Concrete plinths balcony extend into the ground, and it is simple to adjust their length and depth to the site’s requirements. Purchasing precast plintar altan that have been sunk to the proper depth is the simplest option. It is of course possible to create your own concrete plintar altan using casting pipes and aerated concrete if you need to modify the length of your concrete plinths.
Precast concrete plinths
Make a hole big enough to fit the concrete plinth. The height of the plinth, any obstructions in the ground, and whether you want to reach frost-free depth all affect how far you need to dig. Frost-free depth varies widely across the nation and is also influenced by other soil characteristics. Use adjustable pole shoes that are simple to modify both during construction and afterwards in the event that, for instance, the ground should dip a little. After installing the terminals, the surrounding soil should be adequately backfilled and packed.
Laws and the carrying line
The patio should always be fastened to the house wall if at all possible. The remainder of the load-bearing construction may be built on a rule that sits solidly and straight in the home.
Make sure the bolt is level and secure it with an appropriate screw and cap.
The additional studs are subsequently fastened to the wall stud. Normal CC distance between the bars is 600mm, however you may need to reduce it to 400mm if your trolley is narrower (22mm), and you may typically extend it to 800mm if your trolley is thicker (34mm). The bars should be screwed to the concrete plinths balcony and attached.
You may put together the carrying rope before or after the rest of the byggskiva, depending on how the construction site and terrace appear. In the majority of situations, it is really simpler to attach the outside studs first, weigh them down, and temporarily secure them before laying the carrying rope and creating the ultimate balance.
To avoid very strenuous lifting, start with the carrying rope if the patio is particularly large and weighty.
